The ADA accessibility requirements in building codes work as a layered system: the Americans with Disabilities Act and the Fair Housing Act set a federal floor that applies everywhere, while the technical measurements you actually build to come from the International Building Code and its referenced standard, ICC A117.1, adopted and enforced by your local building department. Where the two disagree, you build to the stricter rule. Which specific requirements attach to your project depends on what the building is used for, whether the work is new construction or an alteration, and, for renovations, how much you are spending.
How Federal Law and Local Codes Fit Together
Two federal laws do the heavy lifting. The ADA prohibits disability discrimination in public accommodations, commercial facilities, and state and local government buildings. The Fair Housing Act covers residential construction, requiring specific accessible design features in newly built multifamily housing.1HUD User. Fair Housing Act Design Manual Both apply nationwide regardless of what your local code says, and where a local code is less protective, the federal standard controls.
Enforcement, though, happens through building departments applying the IBC. The IBC references ANSI A117.1 for its technical accessibility provisions, and those provisions are closely aligned with the ADA’s own design standards.2U.S. Access Board. Guide to the ADA Accessibility Standards – Chapter 1: Using the ADA Standards Local jurisdictions adopt the IBC, sometimes with amendments, and enforce it through permitting and inspection. Some states layer their own accessibility codes on top, imposing requirements that go beyond both the model code and federal law. When codes conflict, the strictest applicable standard governs.
Which Buildings Have to Comply
Public Accommodations and Government Facilities
Under ADA Title III, every private business open to the public is a public accommodation: hotels, restaurants, retail stores, medical offices, theaters, and gyms all must provide equal access to goods and services. Government-owned buildings face even more rigorous standards under ADA Title II, ensuring that services like voting, court proceedings, and public meetings are physically accessible.
Multifamily Housing
The Fair Housing Act requires accessible design features in covered multifamily housing built for first occupancy after March 13, 1991.3HUD User. Multifamily Building Conformance With the Fair Housing Act “Covered” means buildings with four or more dwelling units. In buildings with an elevator, every unit must meet the requirements. In buildings without one, only ground-floor units need to comply. Required features include an accessible entrance, accessible common areas, usable doors and hallways, accessible light switches and outlets, reinforced bathroom walls for later grab bar installation, and usable kitchens and bathrooms.
Hotels and Transient Lodging
Hotels, motels, and other short-term lodging must provide a minimum number of guest rooms with mobility features based on total room count. A 100-room hotel needs at least two rooms with roll-in showers. Facilities with more than 500 rooms must provide mobility-accessible rooms equal to roughly two percent of total inventory.4ADA.gov. 2010 ADA Standards for Accessible Design Guest rooms with communication features for people who are deaf or hard of hearing follow a separate table with their own minimums.
Employee Work Areas
Employee-only work spaces get a carve-out, but it is narrower than many developers assume. These areas do not need full accessibility, but they must allow a person using a wheelchair to approach, enter, and exit. That means an accessible route to the door, a compliant entrance, and enough clearance inside for a wheelchair space of at least 30 by 48 inches. In work areas of 1,000 square feet or more, common circulation paths must also be accessible.5U.S. Access Board. Guide to the ADA Accessibility Standards – Chapter 2: New Construction Spaces employees use that are not for work itself, like restrooms, break rooms, locker rooms, and parking, must be fully accessible with no exceptions.
Renovations and the 20 Percent Path-of-Travel Cap
New construction must comply with current standards from the ground up. Existing buildings are not frozen in place, but they are not required to be brought up to code all at once either. Accessibility obligations kick in whenever an owner renovates an area that serves a primary function, meaning any space where a major activity of the business takes place. A restaurant dining room, a retail sales floor, an office suite, and a medical exam room all qualify. Corridors, mechanical rooms, and break rooms do not.
When you alter a primary function area, you also have to make the path of travel to that area accessible. The path of travel includes the route from the building entrance and parking to the renovated space, plus any restrooms, telephones, and drinking fountains serving it.6U.S. Access Board. Guide to the ADA Accessibility Standards – Chapter 2: Alterations and Additions
Path-of-travel improvements are required only to the extent they do not exceed 20 percent of the total cost of the alteration to the primary function area. If full compliance would cost more than that threshold, you spend up to the cap and stop, even if the resulting path is not fully accessible.6U.S. Access Board. Guide to the ADA Accessibility Standards – Chapter 2: Alterations and Additions When the cap forces prioritization, spending follows this order:
- An accessible entrance
- An accessible route to the altered area
- Accessible restrooms
- Accessible telephones and drinking fountains
- Other elements like parking and storage
A $200,000 renovation triggers up to $40,000 in path-of-travel spending. If an accessible entrance and route consume that full $40,000, the restrooms can wait until the next renovation triggers additional obligations. Each separate alteration project resets the 20 percent calculation, so accessibility improvements accumulate over time even when no single project achieves full compliance. Minor maintenance work, like repainting, patching drywall, or replacing fixtures in kind, does not trigger path-of-travel requirements at all.
The Technical Numbers You Will Be Measured Against
The 2010 ADA Standards for Accessible Design contain detailed measurements for nearly every element of the built environment. The numbers below are the federal standards that remain in effect for 2026. Local codes may be stricter, so confirm your jurisdiction’s requirements before finalizing designs.
Ramps and Accessible Routes
Any change in level greater than half an inch along an accessible route requires a ramp. The maximum running slope is 1:12, meaning one inch of rise for every twelve inches of run.7U.S. Access Board. Guide to the ADA Accessibility Standards – Chapter 4: Ramps and Curb Ramps Cross slope cannot exceed 1:48. Landings are required at the top and bottom of every ramp run and at any change of direction. Floor surfaces must be stable, firm, and slip-resistant.
Doors and Thresholds
Doorways must provide a minimum clear opening of 32 inches, measured with the door open at 90 degrees.4ADA.gov. 2010 ADA Standards for Accessible Design Thresholds cannot exceed half an inch in new construction, and any threshold taller than a quarter inch must be beveled at a slope no steeper than 1:2.8U.S. Access Board. Guide to the ADA Accessibility Standards – Chapter 4: Entrances, Doors, and Gates Door hardware must be operable with one hand and without tight grasping or wrist twisting, which is why lever handles appear on virtually every accessibility plan.
Turning Space
Wherever a wheelchair user needs to change direction, the design must provide either a 60-inch-diameter circular turning space or a T-shaped space measuring 60 by 60 inches with each arm and stem at least 36 inches wide.9U.S. Access Board. Guide to the ADA Accessibility Standards – Chapter 3: Clear Floor or Ground Space and Turning Space Restrooms, elevator lobbies, and dressing rooms are the places where turning space most often gets squeezed during construction.
Restrooms
Grab bars in accessible toilet compartments must be mounted so the top of the gripping surface falls between 33 and 36 inches above the finished floor.10U.S. Access Board. Guide to the ADA Accessibility Standards – Chapter 6: Bathing Rooms Sinks must provide knee clearance underneath and insulated or otherwise configured pipes to prevent burns for users who cannot feel contact with hot surfaces. Mirrors above lavatories must be mounted with the bottom edge of the reflective surface no higher than 40 inches from the floor.
Reach Ranges and Operable Controls
Light switches, thermostats, fire alarm pulls, and other controls must fall within a reach range of 15 inches minimum to 48 inches maximum above the floor when approached from the front without obstruction. When a forward reach extends over a counter or shelf deeper than 20 inches, the maximum high reach drops to 44 inches.11U.S. Access Board. Guide to the ADA Accessibility Standards – Chapter 3: Operable Parts All controls must be operable with one hand and no more than five pounds of force.
Parking
Accessible car parking spaces must be at least 96 inches wide with an adjacent access aisle of at least 60 inches. Van-accessible spaces need extra room, provided either by a wider 132-inch space paired with a standard 60-inch aisle, or a standard 96-inch space paired with a wider 96-inch aisle.12U.S. Access Board. Guide to the ADA Accessibility Standards – Chapter 5: Parking Spaces Access aisles must be marked to discourage other drivers from parking in them, and two adjacent spaces can share a single aisle. The total number of accessible spaces required scales with lot size.
Stairways
Handrails are required on both sides of every stairway and must be continuous along the full length of each flight. At the top, handrails must extend horizontally at least 12 inches beyond the last riser nosing. At the bottom, they must continue along the slope of the stairs for a distance equal to at least one tread depth.13U.S. Access Board. Guide to the ADA Accessibility Standards – Chapter 5: Stairways Gripping surfaces must be between 34 and 38 inches above stair nosings, with a circular cross section of 1¼ to 2 inches in diameter.
Signage
Room identification signs must use raised uppercase characters in a sans serif font, between ⅝ inch and 2 inches tall, with contracted (Grade 2) Braille positioned directly below. Tactile signs are mounted with the lowest character baseline at 48 inches and the highest at 60 inches above the floor.14U.S. Access Board. Guide to the ADA Accessibility Standards – Chapter 7: Signs Directional and informational signs that are not room identifiers follow a separate set of rules focused on visual legibility.
Alarms and Assistive Listening
Assembly areas with audio amplification, like theaters, lecture halls, and courtrooms, must provide assistive listening systems. The minimum number of receivers starts at two for spaces seating 50 or fewer and scales upward, and at least 25 percent of receivers must be compatible with hearing aids. Visual alarms with strobe lights are required in public and common areas to alert people who are deaf or hard of hearing during emergencies, and audible alarms must serve those with vision impairments.
Historic Buildings
Historic status does not exempt a building from accessibility. It shifts the analysis from “comply fully” to “comply as much as possible without destroying what makes the property significant.” The 2010 ADA Standards define a “qualified historic building or facility” as one listed in or eligible for the National Register of Historic Places, or designated as historic under a state or local law.4ADA.gov. 2010 ADA Standards for Accessible Design Alterations to these properties must comply to the maximum extent feasible, with an exception when full compliance would threaten or destroy the building’s historic significance.
Triggering the exception requires consultation with the State Historic Preservation Officer, who reviews the proposed modifications and determines whether the changes would compromise the character-defining features that make the property historically significant.15National Park Service. Preservation Brief 32: Making Historic Properties Accessible If the SHPO agrees, alternative methods of access are permitted. Examples include audio-visual presentations showing inaccessible upper floors, tactile scale models, interpretive panels at inaccessible viewpoints, and home delivery of services.
Tax Credits and Deductions That Offset the Cost
Two federal tax provisions help absorb the price of accessibility work. Small businesses may be eligible for the Disabled Access Credit under Section 44 of the Internal Revenue Code. The credit covers 50 percent of eligible access expenditures that exceed $250 but do not exceed $10,250 in a given tax year, producing a maximum annual credit of $5,000.16Office of the Law Revision Counsel. 26 U.S. Code 44 – Expenditures to Provide Access to Disabled Individuals To qualify, a business must have had gross receipts of $1 million or less, or no more than 30 full-time employees, in the preceding tax year.
Any business, regardless of size, can deduct up to $15,000 per year for expenses incurred to remove architectural and transportation barriers at facilities used in a trade or business.17Office of the Law Revision Counsel. 26 U.S. Code 190 – Expenditures to Remove Architectural and Transportation Barriers to the Handicapped and Elderly The two provisions can be used together in the same tax year. A small business that spends $20,000 on ramp construction and restroom modifications could claim the $5,000 credit and deduct $15,000, reducing the net outlay considerably.
Permits, Inspections, and Penalties
Getting a building permit for accessible construction requires detailed drawings that call out every accessibility feature: door swing directions, clear widths, counter heights, ramp slopes, grab bar placements, and the location of accessible seating. Site plans must show a continuous accessible route from public transportation stops and parking areas to the building entrance. The permit application asks for the building’s occupancy type and construction class, and getting that classification wrong at the permit stage means the wrong regulations get applied, surfacing as a problem during inspection when it is far more expensive to fix.
Inspectors visit at multiple stages, most critically when framing is exposed and after final finishes are applied. Finish materials deserve particular attention: flooring thickness, wall coverings, and built-in cabinets can all shrink critical clearances below the minimum after earlier framing inspections passed. A hallway measuring 44 inches wide at framing might drop below minimum after tile, baseboard, and handrails go in. If an inspector identifies a violation, work stops until the correction is resolved and reinspected. Successful completion leads to a Certificate of Occupancy.
Ignoring accessibility requirements produces consequences well beyond fixing the problem later. Under ADA Title III, the Department of Justice can seek civil penalties that, as of a 2014 inflation adjustment, were set at up to $75,000 for a first violation and $150,000 for subsequent violations.18ADA.gov. Civil Monetary Penalties Inflation Adjustment Under Title III Those amounts are adjusted upward annually for inflation, so current maximums are higher than the 2014 figures. Private individuals can also file civil lawsuits seeking injunctive relief, and in many states can recover monetary damages and attorney fees. Courts can order mandatory retrofitting, which often costs several times what compliant construction would have cost originally. For multifamily housing that violates the Fair Housing Act, HUD can pursue enforcement actions that include penalties and mandatory modifications across an entire development. The cheapest time to build accessibly is always the first time.